- Bearings
- ASAHI
- IJK
- IKO
- INA
- JTEKT
- KOYO
- NACHI
- NIS
- NSK
- NF203-NF320
- NSK 1200-2322
- NSK 16002-16017
- NSK 21300-22348
- NSK 23000-24100
- NSK 29300-29400
- NSK 30200-30320
- NSk 30300D-30320D
- NSK 32000
- NSK 32200-32300
- NSK 51100-51430
- NSK 5200-5315
- NSK 6000-6040
- NSK 607-735
- NSK 6200-6240
- NSK 6300-6340
- NSK 6403-6417
- NSK 6800-6834
- NSK 6900-6930
- NSK 7000 PRECISION
- NSK 7000-7338
- NSK 7200 PRECISION
- NSK 7900 PRECISION
- NSK Adapter
- NSK BL205-317
- NSK Grease
- NSK Housing
- NSK N200-N418
- NSK NJ202-NJ2320
- NSK NN3006-3038
- NSK O-04 - 28
- NSK Ring
- NSK RLS 4-24
- NSK RS-5008
- NSK Seal
- NU202-NU2320
- NTN
- SKF
- TIMKEN
- Others
- Belts
- Power Transmission
- Abrasives
- Blower
- Castor Wheel
- Chain & Sprocket
- Fasteners
- Gear Reducer
- Industrial Fan
- Janitorial & Cleaning
- Ladder
- Lubricant
- Lubricants, Coolants & Fluids
- Lubrication Equipments
- Motors
- Oil Seal
- Oiless Bushing
- Pneumatic Equipments
- PROMOTION ITEMS
- Pulley
- Water Pump
- Yamada AODD Diaphragm Pump
- Others
- Others
Merns (M) Sdn Bhd
37, Jalan Sb Indah 1/2a, Taman Sungai Besi Indah, 43300 Seri Kembangan, Selangor, Malaysia.
NDP-15FPH
Previous | 4 / 171 | Next |
Nominal diameter | 1/2 ″ (15A) | |
Material connection | Inlet | Rc1 / 2 |
Discharge port | ||
Air connection | Supply port | Rc1 / 4 (with air cock) |
exhaust port | Rc3 / 8 (with muffler) * | |
Service air pressure | 0.2 to 0.7 MPa | |
Discharge pressure | 0.7MPa | |
Discharge rate / cycle | 70mL | |
Slurry limit (maximum passing particle diameter) | 1mm or less | |
Mass |
-15BA NDP: 4.1Kg NDP-15BS ¡õ: 6.3Kg NDP-15FP ¡õ: 3.5Kg NDP-15FVT: 4.3Kg |
* The silencer is built into the pump body.
Rc3 / 8 screw holes are machined for connecting hoses to guide exhaust to ducts.
Since the NDP-15 series uses the DP-10 series diaphragm, select the NDP-20 series that is one size up for large-scale operation at 20L / min or higher. NDP-15BA ¡õ series uses nylon (PA) as the material for the valve receiver. Pay attention to corrosion resistance. Not suitable for MEK etc. |
Body (wetted part) material | Diaphragm material | ||||
C: Chloroprene (CR) |
N: |
T: Fluorine resin (PTFE) |
H: |
S: Polyolefin-based thermoplastic elastomer (TPO) |
|
A: Aluminum alloy (ADC12) |
NDP-15BAC (851946) |
NDP-15BAN (851947) |
NDP-15BAT (851945) |
NDP-15BAH (851948) |
NDP-15BAS (852680) |
S: Stainless steel (SCS14) |
NDP-15BSC (851958) |
NDP-15BSN (851959) |
NDP-15BST (851957) |
NDP-15BSH (851960) |
NDP-15BSS (852681) |
P: Polypropylene (PPG) |
NDP-15FPC (851903) |
NDP-15FPN (851943) |
NDP-15FPT (851698) |
NDP-15FPH (851905) |
NDP-15FPS (852683) |
V: Polyolefin full oil (PVDF) |
--- | --- |
NDP-15FVT (852141) |
--- | --- |
Note) Clicking the model / product number will display the parts list and parts exploded view.
Model |
NDP-15BA ¡õ |
NDP-15BS |
NDP-15FP |
NDP-15FVT |
Ball valve Flat valve |
NDP-15FP ¡õ / NDP-15FVT ・ ・ ・ PTFE |
|||
Valve seat |
A5056 |
SUS316
|
PPG |
PVDF |
Valve holder |
PA |
|||
Center disc |
A5056 |
PPG (SUS304 *) |
PVDF (SUS304 *) |
* SUS304 is insert material
¡ï Valve model
NDP-15BA ¡õ / NDP-BS ¡õ ・ ・ ・ Ball valve
NDP-15FP ¡õ / NDP-15FVT ・ ・ ・ Flat valve ¡ï The flat valve type cannot handle slurry.
¡ï The initial self-priming lift is 1m for all models.
The maximum operating pressure of the body wetted part resin type (FP ¡õ / FVT) is It depends on the liquid temperature. Be sure to check the liquid temperature-maximum working pressure diagram. |